I'm still thinking about how to add rod holders without them being permanently attached in the gunwales. I know I can do the flush mount plates but I'm just not ready to go there yet.
I like the way the Angler looks with the side rails and they do allow me the option for non-permanent attachment.
I was wondering if anybody had bought these rails from ranger and put them on an 1850 reata? What did they cost? Is there a supplier for these other than ranger or do they custom make them to fit? I intended to call them this week but I've just been to darn busy.

Best regards,

I had the flush mounts on the prior boat. They were OK but I found I would have liked to move the rod holders depending on what I was targeting, boards, eye's, muskie...etc. It seemed each method called for different placement.

On the 1850 I had both front and rear rails installed, I move them around several times a year, depending on how many are in the boat, etc. Rails are the way to go imho. You can buy aftermarket rails from cabelas. But, I found the cost difference was minimal, so went with ranger rails. I couldn't tell ya what the cost was, it was to long ago. The fronts are contoured to the gunnel so they fit perfectly. I also like the rails for tying off bumpers.

BIRDDOG

The Ranger 44" S.S. Side rails are $100. I put these on my 1860 as the boat did not come with them.

Check out my photo gallery for the best detachable rail mount rod holders on the market, if you need info on them just ask, they are Cisco's I have them on my Ranger.

I live 33 miles from the Ranger factory in Arkansas and I went down there and purchased 4 rails for my 1850. I purchased the smaller rails and the 4 of them cost me $260 and I installed them myself. They came out quite well and I would recommend this method of installing rod holders on an 1850.

Bob

I had the flush mounts on the prior boat. They were OK but I found I would have liked to move the rod holders depending on what I was targeting, boards, eye's, muskie...etc. It seemed each method called for different placement.

On the 1850 I had both front and rear rails installed, I move them around several times a year, depending on how many are in the boat, etc. Rails are the way to go imho. You can buy aftermarket rails from cabelas. But, I found the cost difference was minimal, so went with ranger rails. I couldn't tell ya what the cost was, it was to long ago. The fronts are contoured to the gunnel so they fit perfectly. I also like the rails for tying off bumpers.

BIRDDOG

How do the bow rails work if I have a trolling motor? Will it clear?

Ranger says they have 44"and 56" stern rails for the Reata. They also list bow rails. Anybody have a picture of the bow rails on a reata? Or better, one with both.
I'm thinking the 44"stern rails will suffice but I can't decide.
They say pictures are worth a thousand words.
Thanks,

My trolling motor fits with the front rails installed with no problem on my 1850.

Bob

I went with the 44" for my 1860 because you can install them forward enough to leave a space behind them that is smooth gunnel so it is easier getting into the boat while on the trailer.
I decided not to go with any bow rails because they looked like a possible trip hazard stepping from the dock to the boat or visa versa. Just my opinion.

Ranger says they have 44"and 56" stern rails for the Reata. They also list bow rails. Anybody have a picture of the bow rails on a reata? Or better, one with both.
I'm thinking the 44"stern rails will suffice but I can't decide.
They say pictures are worth a thousand words.
Thanks,


The bow mount has plenty of clearance, non issue. As far as the stern rails...I tried like heck to get the longer ones. At the time it was a issue, backordered, then they don't make them, then...always an excuse why I couldn't get them.

I opted for the shorter ones in the end. They work well, but I do wish I had the longer at times so I had more options for rod holder placement.

Here is a pic of my rig, you can see the rails/placement. Wish I had a better pic for ya but boat is at the lake.
http://s299.photobucket.com/albums/mm302/Went1976/?action=view&current=P1010140.jpg

BIRDDOG

Thanks, Guy's,
I appreciate your input in the matter.

BIRDDOG, Thank you for the picture. That's a fine looking rig.

I think I'll order the 44" rails, they will work fine for me.
I need to think about the bow rails, though. They don't look like much of a hazard mounted as far back as on BIRDDOG's rig.

Thanks again you were a great help.

LIVE LONG AND PROSPER

I am considering a Ranger 620/621 in the future and was wondering how wide the gunwales are and if they are flat; if wide and flat enough I would suggest mounting a Berts Track system.

Cheers,
Lundfisher

I think I'll order the 44" rails, they will work fine for me.
I need to think about the bow rails, though. They don't look like much of a hazard mounted as far back as on BIRDDOG's rig.



The front rails aren't in the way at all. Where they're placed is the factory mounting position. As far as docking and the rails being in the way, not at all. Mom's, dad's, grandparents and kids...no one has tripped on them. I do like the bow rails for tying off the bumper on the bow, the front cleat is to far forward to tie off the bumper, it offers no protection up there due to the curve of the boat. You can actually see in my pic the black bumper rope tied off to the rail. When I'm up front casting, I generally have 3-4 rods up there, when it's time to move I use a bungy to strap them down to the rail as well. So it comes in handy.

BIRDDOG

I am considering a Ranger 620/621 in the future and was wondering how wide the gunwales are and if they are flat; if wide and flat enough I would suggest mounting a Berts Track system.

Cheers,
Lundfisher


They aren't wide enough for any track system, unless you go with the rail mounts that allow you too hook a track to it. I was exploring a small track to mount riggers on my 621 no go, I also considered a gimble mount but my dealer said can't do that either due to all the wires being ran through the side of the boat and the gimble is to long.

Cisco rail mount quick release mounts and holders are the best rod holder system for Ranger rails, Ram's are okay but they suck for pulling dipsey's and they aren't worth a **** for steelie or salmon fishing. Bottom bouncing off the corners, the best.

I ordered rails and am very glad. I got the shorter ones in back and wish I'd done longer ones. The front ones aren't nearly as big a trip hazard as the Terrova in my experience...don't ask...

I love the rails and wouldn't be without them.