Home   |  Message Board   |  Information   |  Classifieds   |  Features   |  Video  |  Boat Reviews  |  Boat DIY
Walleye Message Central - Reply to Topic
Walleye Message Central

Go Back   Walleye Message Central > Boats, Motors, Electronics and Trailers > Boats > Boat Grab Handle Mounting Question

Thread: Boat Grab Handle Mounting Question Reply to Thread
Your Username: Click here to log in
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-26-2021 07:24 AM
markb11 Thanks for all the great suggestions...as always the WC community comes thru!

Since curve is 1/16 - 1/8, I plan on figuring out the radius, cutting a wooden circle for same, glue sandpaper to OD of wooden circle, chuck up in drill and sand the solid grab handle mounting surface to duplicate the curvature for a solid mount.

Thanks again for all the help.
09-22-2021 11:03 AM
REW P.S.
Also for mounting such a grab handle on the fiberglass surface, be sure to use thru bolts through the fiberglass along with a backing plate on the inside of the fiberglass surface with fender washers and stainless steel locking nuts to insure a long lived permanent installation.

Best wishes
09-22-2021 11:00 AM
REW Mark,
You use the word - SLIGHT - when referring to the curve on the mounting surface.

I would measure the height of the curve and then take a look at the object that you want to mount on that surface.

For myself, if the difference was only 1/16th or so, I would use a sander or grinder on the objects mounting face and grind material off of the object to be mounted so that the object mounted perfectly on the surface.

For this particular item, I am making an assumption that it is solid metal and not hollow.

If the item was hollow, of course I would then use a shim as has been suggested by others.

If you do have a solid object and it would make sense to have the base of the object changed to match the contour of the mounting surface, but do not have the tools to do the shaping, then - swing by a machine shop and have them mill the part to perfection before mounting.


Take care
09-22-2021 09:05 AM
Huntindave I use thickened epoxy to "cast" an exact fit shim. This will give you full support for your grab rail handle. Also depends on how the hull is formed (hollow core, foam core, single layer) at the exact point at which one is going to be mounting the hardware.

Do a you tube search for "bedding boat hardware in thickened epoxy" for more information.
one example;
https://www.youtube.com/watch?v=L-Y0cIS6fSA
09-22-2021 08:31 AM
Misdirection I'd try toilet shims. You can grind down or cut off any excess that shows.

Sent from my SM-A505U using Tapatalk
09-22-2021 08:26 AM
therealjoeblow Find someone with a 3D printer to print you some custom wedges out of a high density material to go under the mounting pads of the handle.
09-22-2021 07:15 AM
markb11
Boat Grab Handle Mounting Question

I’m mounting a single handle DIVE-N-DOG L-F-12-1 STAINLESS STEEL 12 INCH LONG FEMALE CUSTOM EXTRA WIDE BOAT GRAB RAIL / HANDLE to the back of my 219 Pro V GL to assist with getting back in the boat via the 3 step ladder I installed. The question is, the mounting surface where I need to put the handle has a slight curvature to it…so…what should I use between the handle mounting area and the fiberglass boat mounting surface to negate the slight curve? Any suggestions? Thanks in advance for your valued input.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


All times are GMT -6. The time now is 12:49 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.